DF-96B Automatic Water Level Controller with stainless steel probe for intelligent home

This product uses the integrated circuit , combined with the high-rise buildings , the sink ( water tower ) is designed to enhance the classification level , with joint control up and down the pool , pond drainage and water protection and other functions, can automatically tank water , drainage, and effectively prevent pool water level is too high idling spill or overflow damage , is an industrial , household products are applicable . Very suitable for urban, rural , schools, industrial and mining enterprises and family pool water - Well Water works widely in printing and dyeing , chemical, food , beverage, brewing and sprinkle sugar industries .
( A ) single control head on the sink installation instructions to install the control diagram shown in Figure 1 :
A ( red ) - the upper pool ( water tower ) upper level control point , the water level rises to reach point A water level, water in contact with the probe, the water level controller automatically shuts the pump ;
B ( blue line ) - the upper pool ( water tower ) the lower level control point , the water level drops below the water table to point B , the probe out of contact with water , the water level controller automatically open the pump , pool filled with water ;
C ( black line ) - for the pool ( water tower ) ground , the lowest point on the tank in contact with the bottom of the pool ;
D ( green line ), E ( yellow line ) points and received C.
(B ) under the control of a single pool ( ie drainage pond ) probe installation instructions to install the two shown in Figure :
E- limit pond level control for the next point , the water level rising water level reaches the point E , the water in contact with the probe , the water level controller automatically open the pump , pond drainage ; Without drainage, the E point is not connected ;
D- limit for the next pond level control point , the water level dropped to D level , water and probe disengagement , water level controller automatically shuts the pump to stop the drainage basin ;
C- ground pool is placed in contact with the lowest point of the tank bottom of the water ;
A, B point is not connected .
(C ) water protection probe installation instructions to install the diagram shown in Figure 3 :
C, D point to the lower pool level control point , the water level down to the lower level , C, D probe and the surface of the disengagement , water level controller relay immediate action , cut output, the pump stopped working ;
Point C and point E shorted ;
A, B point is not connected .
(D ) joint control up and down the pool installation instructions to install the probe is shown in Figure III:
A- is the pool ( water tower ) ceiling level control point , the water level rises to reach point A water level, water in contact with the probe, the water level controller automatically shuts the pump ;
B-is the pool ( water tower ) Lower level control point , the water level drops below the water table to point B , the water and the probe disengagement , automatic level control pump , pool filled with water ;
C- upper , without the pool ( water tower ) public ground , on the lowest point of contact with the bottom of the sink basin ;
D- limit for the next pond level control point , the water level dropped to D level , water and probe disengagement , water level controller automatically shuts the pump to stop the drainage basin ;
E- limit pond level control for the next point , the water level rises to the point E water level, water in contact with the probe , the water level controller automatically open the pump , pond discharge head ; Without drainage, the E point is not connected .
Mounting Dimensions
Other installation instructions
1 , in order to ensure the level controller to work properly, please check again after installing input and output wiring, the probe cable is reliable contact. Can move up and down the probe to touch , out of the water , the water they detect simulated controller is installed correctly and is working properly according to your needs .
2 , recommended that the probe fixed points in the pool wall, so as not to cause the probe position shifted level controller malfunction ( if water is a metal wall , in addition to point C should not be connected to the ground outside the wall, in order to avoid a short circuit , causing the water level The controller does not work ) .
3 , according to the above wiring is connected, check the right of the product "Manual / Auto " switch (DF-96D no ) , whether indeed according to user need to manually turn on , turn off the pump , after the adjustment back with "auto " position level controller into operation .
4 , the temporary need to open , close pumps, water level controller , please use the left side of the "Manual / Auto " switch control (DF-96D) type without a manual switch.
5 , to avoid malfunction , do not install the product in damp , corrosion and high metal content of the gas environment.
6 , it is recommended that you complete control of the use of water produced special probe.
7 , in order to ensure that the water level controller is working properly , check the monthly water level probe cleaning 1-2 times.
Troubleshooting
1 , power does not work:
. a check whether the red power indicator light , if not light, check whether the input and output terminals have good contact ;
b. " Manual / Auto " switch to check the product on the left side , is in the " OFF" will adjust back to " Auto " position , the water level controller into working condition.
2 , above or below the water line probe control point , the pump does not automatically close or open , press the " Auto / Manual " switch to manually control the pump . And check :
. a probe has deviated from its original position, the placement of high ( low ) , resulting in the water level can not reach ( out ) ;
. b upper and lower water level , ground probe whether the connection with other lines of dislocation , if there is a wrong or short ;
c probe whether the corrosion and shedding phenomenon, the product line and the probe is connected between the probe and the probe cable is good contact . ;
dC ground point is placed in the pool has the lowest position .